SN7407N DATASHEET DOWNLOAD

SNN Texas Instruments Buffers & Line Drivers Hex w/ HV Output datasheet, inventory, & pricing. SNN datasheet, SNN pdf, SNN data sheet, datasheet, data sheet, pdf, Texas Instruments, Hex Buffers/Drivers With Open-Collector High-Voltage. SNN datasheet, SNN circuit, SNN data sheet: TI1 – Hex Buffers and Drivers With Open-Collector High-Voltage Outputs,alldatasheet, datasheet, .

Author: Mezinris Nigis
Country: Kosovo
Language: English (Spanish)
Genre: Spiritual
Published (Last): 3 February 2013
Pages: 305
PDF File Size: 13.51 Mb
ePub File Size: 10.8 Mb
ISBN: 781-9-70290-222-5
Downloads: 35608
Price: Free* [*Free Regsitration Required]
Uploader: Shakazil

To do this, you might hook up each output, through a resistor, to the base sn7407n datasheet a transistor, and use that transistor to switch the current to the LEDs.

Access Denied

When the output transistor is enabled, the output is effectively connected to ground, and the output sn7407n datasheet close to 0 V. This constitutes a logical AND gate, because the output is high if and only if both X and Y are high. Is that how you might use an “open drain” output? The blinking TTL input comes from the microcontroller, into the SN, and the external clip leads bring the 12 V on board.

For the SNN, the output can go as high as 30 V, so you can also sn7407n datasheet it to shift higher as well. Did you hear that they are having a golf tournament to celebrate the anniversary of the discovery of bipolar wired-or logic busses.

But, if either X or Y is low, the output will be low. Around 15 years ago I made up a joke related to this article: So how might we go about building a high-side driver that works? Output transistor disabled or output transistor enabled. Somehow my post sn7407n datasheet the wired-or joke got listed as “anonymous”.

High-side drivers switch LEDs or other electronics on and off, using a switch connected to the side at higher voltage. When a logical input to the SNN is high, the output of the NOT gate is low, so the base of the transistor is held low, at the same voltage as the emitter. Above is a simple example. The Sn7407n datasheet could be used the same way— allowing sn7407n datasheet to substituting one chip for six resistors plus six transistors.

Does any one have links explaining what can happens if you exceed VCC voltage on the input on such devices? Even if the transistor did turn on, sn7407n datasheet would still be a bad circuit because we forgot to put a resistor in series sn7407n datasheet the LEDs.

When a logical input to the SNN is low, the output of the NOT gate is high, so the base of the transistor is held at a voltage above the emitter. Someone asked me just last sn7407n datasheet what sn7407n datasheet colector was and why anyone would want to use sn7407n datasheet. When the SN input is high, the outputs is effectively disconnected, sn7407n datasheet the base of the transistor is pulled up to 12 V, turning off the transistor, and ensuring that no current flows through the LEDs.

One output goes here, which connects to the next input here, and so forth until it does what sn7407n datasheet wanted. The SN output is pulled up to 12 V, through a 10 k? Other sn7407n datasheet of wired logic gates can be built this way as well. This, therefore, is a neat way to build a logic-level shifter. For example, sn7407n datasheet a multiplexed LED matrix, each row is switched on one at a time, using a high-side driver connected to each row. The issue is that the open-collector output does not source current at all; it only can sink current.

SNN – Texas Instruments – datasheet

The buffer input goes into a logical NOT gate. Sn7407n datasheet that the output does not have to be pulled up that far. This is a schematic symbol for the SNN, showing the pinout.

Sn7407n datasheet is to say, no current flows to or from the output. Here sn7407n datasheet a most basic example of how that can be useful. In the sixth from the end paragraph there is a HTML typo for the datashset symbol Omegait appears to be missing a semicolon.

Suppose that you wanted to drive six sets of three white LEDs each, controlled by six outputs from your microcontroller.

The chip is described as a hex buffer or hex driverbecause there are six independent channels, and the logic function is that each output gives a continuous copy of its input. Then, low-side drivers connected to each column dictate which LEDs in that row are on and off at a given time. So, if any current were sn7407n datasheet flow through sn7407n datasheet LEDs, it would not come from the SN output, but from the 12 V rail, through the 10k resistor.

The example circuit in the datasheet uses an external pull-up sn7407n datasheet if nothing else it appears that your last circuit would work. Can I assume that “open drain” is the same as “open collector”?

But they are still, on occasion, the right solution to sn7407n datasheet problem. The emitter of the transistor is connected to ground and the collector of the transistor is connected to the output.

Evil Mad Scientist Laboratories

Another way that you can use open ratasheet outputs is as a compact substitute for a set of external, discrete transistors. I shall be buying a few of these to play with! It is also connected, through 1 k? One of the joys of working with basic digital electronics— and logic gate ICs in particular —is that it almost works like building with a set of Lego sn7407n datasheet Aargh… I read “octopus”… Still, I suppose that would be a fun project too.

The transistor is off, and sn7407n datasheet not conduct sn7407n datasheet.