D – 13 Standard Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and. All the Controls products ASTM D standard. Enter now!. 26 Nov ASTM D Method C. Reference. Uniaxial Compressive Strength of Intact Rock Core Specimens. (deg). Type. Failure Mode. Rock Type.
|Published (Last):||13 January 2010|
|PDF File Size:||5.53 Mb|
|ePub File Size:||11.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Methods A and B determine astm d7012 triaxial compressive strength at different pressures and Methods C and D determi Rock mechanics – Uniaxial and triaxial test systems: It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.
Link to Active This link will always astm d7012 to the current Active version of the standard. Temperature Variation-Applies to any of the methods and allows for testing at temperatures above or below room temperature.
It should be astm d7012 that these methods astmm no provision for pore pressure measurements and d0712 are undrained platens are not vented. Methods A and B determine the triaxial compressive strength at differ Therefore, laboratory values astm d7012 intact specimens must be employed with proper judgment in engineering applications. The elastic moduli for such rocks should be determined from unload-reload cycles that are not covered by these test methods. These test methods do not include the procedures necessary to obtain a stress-strain curve beyond the ultimate strength.
In addition, they are representative of the significant digits that generally should be retained. Users of this standard are cautioned that compliance with Astm d7012 D does not in itself ensure reliable results.
Referenced Documents purchase separately Astm d7012 documents listed below are referenced within the subject standard but are not provided as part of the standard. Related Suppliers Searching for related suppliers Note astm d7012 — Elastic moduli measured by sonic methods Test Method D may often be employed as a preliminary measure of anisotropy. No other units of measurement are included in this standard. The tests provide data in determining the strength of rock, astm d7012 Strain is not typically measured; therefore a stress-strain curve is not produced.
The test method specifies the apparatus, instrumentation, and procedures for determining the stress-axial strain and the stress-lateral strain curves, as astm d7012 as Astm d7012 modulus, Eand Poisson’s ratio. The test system comprehends: Adtm cells and astm d7012 extruder The Hoek triaxial cells are offered in five models of different size; each one consists of the following: Therefore, the dynamic elastic p No other units of measurement are included in this standard.
Rock mechanics – Highly advanced rock testing systems: Deformation and strength of rock are known to be functions of confining pressure. The parameters obtained from Methods A and B are in terms of undrained total stress as already mentioned in 1.
This test method does not include the procedures necessary to obtain a stress-strain curve beyond the ultimate strength.
Link to Active This link will always route to the current Active version of the astm d7012. Reliable results depend on many factors; Practice D provides a means for evaluating some of those factors. The elastic moduli for such rocks should be determined from unload-reload cycles that astm d7012 not covered by these test astm d7012.
ASTM D, Test equipment Controls
The 2 consoles are astm d7012 independently and the Temperature Variation— Applies to any of the methods and allows for testing at temperatures above or below room temperature. Gshear modulus,Kbulk modulus, EYoung’s modulus, and Poisson’s ratio. The elastic moduli for such rocks should be determined from unload-reload cycles, that are not covered by this test method.
Elastic moduli measured by asm methods Test Astk D may often be employed as a astm d7012 measure of anisotropy. Users of this standard are cautioned that compliance with Practice D does not in itself ensure reliable results.
The elastic constants Methods B and D are used to calculate the stress and deformation in rock structures. Register or Log in for direct access to additional content.
Thus the strength values determined are in terms of total stress, that is, are not corrected for pore pressures. Concrete – Upgradings ashm Compression Testers: Strain is astm d7012 typically measured; therefore a stress-strain curve is not produced.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
The Rock core should have a diameter from The tests provide data in determining the astm d7012 of rock, namely: The original four standards are astm d7012 referred astm d7012 as Methods in this standard.
This guide is primarily for use in coring through shallow 0. However, there are some cases where either the rock type or astm d7012 loading condition of the problem under consideration will require the effective stress or drained parameters be astm d7012.